When your exterior starts failing, the clock is already ticking. Forge Siding provides full Siding in Allentown, PA — from initial assessment to final cleanup — so your home is protected and your curb appeal restored.
Forge Siding grew out of a simple frustration: too many Allentown homeowners were paying good money for Siding work that failed inside five years. Wrong profiles, wrong fastener gauges, no housewrap — then the callbacks never came. We do it right the first time, using manufacturer-recommended installation methods and materials rated for PA's specific climate demands.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Most homeowners don't notice siding problems until water damage has already reached the sheathing. These are the signals worth acting on before the repair scope doubles.
Even a small gap at a butt joint or around a window trim is an entry point. Water wicks in, freeze-thaw cycles widen the gap, and the damage compounds every winter.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Interior peeling close to an outside wall isn't a paint problem — it's a moisture infiltration problem. Your siding is the likely culprit and ignoring it turns a siding job into a drywall and mold job.
Panels that have pulled away from the wall are an open door for pests, moisture, and cold air. Nails back out over time when the substrate is soft — often a sign of prior water damage underneath.
Old or failing siding, particularly if the housewrap underneath has deteriorated, acts like a thermal short-circuit. Your HVAC runs harder to compensate, and the bills reflect it before the siding looks obviously bad.
Heavy algae or mold staining on the exterior surface isn't just cosmetic — it means the surface is retaining moisture long enough for organic growth. That moisture is also working its way into the wall system.
From a single damaged panel to a complete re-side on a large commercial property, we handle the full range of exterior cladding work — and we do it with the same crew standards regardless of job size.
Fiber cement is the workhorse material we recommend most in PA's climate — it handles humidity, impact, and UV better than most alternatives and carries manufacturer warranties that actually hold up. We're certified installers for HardiePlank, HardieShingle, and competing fiber cement systems. Installation follows manufacturer specs to the millimeter: correct lap, correct fastener type and spacing, correct clearance from grade and roof surface, and full housewrap integration on every project.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for PA's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
Engineered wood is popular in Allentown neighborhoods where the traditional wood look matters architecturally but the maintenance demands of real cedar or pine aren't practical. We install with stainless or hot-dipped galvanized fasteners to prevent iron staining at the nail head — a detail that separates a professional installation from a quick flip job.
Not every siding problem needs a full re-side. Storm impact, vandalism, or isolated rot can often be addressed with a targeted repair that blends into the existing field. We stock common profiles and can often source discontinued patterns through our supplier network for historic or older homes where matching matters. Partial replacement work is priced honestly — if we see a repair scope that's going to creep, we say so before we start, not after.
We work with metal panel systems, large-format fiber cement, and commercial-grade vinyl for multi-family and light commercial applications. EIFS compatibility work, expansion joint detailing, and coordination with waterproofing and window subcontractors are all in scope. We carry the insurance requirements for commercial GC work and can provide certified payroll documentation for public projects.
Siding that terminates at rotted or missing fascia boards isn't protected — it's channeling water straight into the rafter tails. We routinely pair siding replacement with trim, soffit, and fascia work so the entire exterior envelope is addressed in one mobilization rather than two. PVC trim board, prefinished aluminum coil, and fiber cement fascia are all in our wheelhouse.
Four steps. Each one documented. No surprises at the invoice.
A thorough inspection before we quote means the estimate we hand you is accurate. We check the substrate, the existing housewrap or vapor barrier, window and door flashing, corner and soffit condition — all of it — so there are no hidden surprises once demo starts.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
Installation follows manufacturer specs and local building code. When work is complete, the lead installer does a quality check before calling you for the final walkthrough. You inspect every elevation — we go through it with you, address anything that needs attention, and make sure the site is clean and restored before we invoice.
We don't sub out work to unlicensed handymen to cut costs. Every installer on a Forge Siding project is a W-2 employee or licensed sub with verified credentials and completed manufacturer training.
Upfront pricing means you know what you're paying before a single panel comes off the wall. Change orders require your written approval. We've built our reputation in Allentown, PA on the fact that our estimates are reliable.
When we book your project, we commit to a start date. No bumping you for a bigger job, no weeks of silence after signing. We operate with enough crew capacity to honor the schedule we gave you.
Old siding demo generates a lot of debris — old panels, nails, housewrap, fasteners. We haul it out daily. Your driveway, lawn, and landscaping are clean at the end of every work day — not just at project completion.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Talk to Us About Your Project — +1-844-782-0929Straight from the homeowners we've worked with across Allentown and Allentown, PA.
We had three other quotes before calling Forge Siding. The difference was the inspection — they actually walked the whole house with a moisture meter and found soft sheathing behind two panels on the north wall that nobody else mentioned. The estimate covered the sheathing repair too, so no surprise charges when demo day came. Final result is clean and tight. We'd hire them again without hesitation.
A storm took out a whole section of vinyl on the east side of our house. I called four contractors — three of them said they'd have to replace the entire elevation because they couldn't match the profile. Forge Siding's estimator sourced a matching panel through their supplier network and did a clean repair. You can't tell where the new material starts. Saved us probably $4,000 compared to a full-side re-do.
The fascia and soffit on our older home were rotting away and we assumed it would be a nightmare project. Forge Siding quoted it alongside the siding replacement so everything was done in one mobilization. The crew found two spots where the rafter tails had started to soften — they showed me photos before touching anything and walked me through the repair options. The whole exterior looks like a different house now.
The estimate process was refreshingly honest. The estimator told me upfront that my old OSB sheathing had delaminated in two areas and would need replacement before new siding could go on — with photos and a written line item. No one had mentioned that in the other quotes. Forge Siding fixed the sheathing, installed the HardiePanel system, and the project cost exactly what they quoted including the repair.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Allentown, PA don't do it this way.
I needed a quick turnaround on a rental property before a new tenant moved in. Forge Siding fit us in on short notice, did a clean vinyl replacement on two elevations, and the inspection cleared without a single callback item. Responsive, professional, priced fairly. That's all I ask for and they delivered all three.
Real questions, real answers — no filler.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Allentown, PA. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Reach us at +1-844-782-0929 and we'll confirm service at your location. Most addresses in and around Allentown are within our standard service radius with no travel fee.
Free written estimate. Licensed crew. Scheduled start date. Call Forge Siding now and get a real assessment — not a ballpark number over the phone.
Schedule My Assessment — +1-844-782-0929